Connecting Your Car Speakers to an Amp Use Your Factory Wiring
Seth, The turn-on lead in the diagram is shown split like that for clarity. Jeremy, If you bought your amplifier at Crutchfield, you could call Tech Support for free help troubleshooting your system. And why do I need to use a ground block?
Do you have a diagram or advice on best way to do it? As for what speakers and amp to get, why don't you or your daughter give us a toll-free call at and talk to an Advisor for help building the best system. Buck, Last question, I promise. Make sure and secure, with nonconducting tape or tie-off, any wiring connector from making contact with metal, which could cause interference or damage the receiver. Your amp circuit breaker protects your power cable and car from catching fire in the event of a short circuit.
Maybe looking at the photo and its captions will help you visualize how this saves running speaker wire throughout the car to each speaker. If you are referring to a car system, then you can follow the article diagram using only those components relevant to your situation. Does it need to go as far back as possible? You want an amp more powerful than your sub, because you don't want your sub to clip. If that's not it, trace your wires to make sure they are connected.
For more specific options, just get in touch with a member of Crutchfield's Sales Advisor Team via phone or chat - just click on the Contact Us link at the very top of this page. Make sure you always turn off your amp when you leave your car, it will overheat and drain your battery. Caleb, If you bought your gear at Crutchfield, you could call Tech Support for free help troubleshooting your system. Wayne, When replacing speakers and wiring, after disconnecting the factory wiring from the speaker, you can leave it installed as it was.
It's not until you're installing three or four devices that you start needing a relay. Hi Buck, I have an Alpine setup and wanted to add another sub amp to it. If you are using a factory radio in your system, start by getting an amp with speaker-level inputs. How to install coaxial car speakers. The processor will create the subwoofer channel outputs from the other inputs.
When connecting a line out connector to a factory head unit, it is advisable to use both sets of speaker wires to maintain the left and right stereo effect from modern music. If you buy your wires from Crutchfield, you could call Tech Support for free help wiring your system. Rick, You won't need any line output converters if you use amplifiers with speaker-level inputs. To do that is it something as simple as just unplugging the wire from the old speakers and plugging them into the new ones? Give us a call at and an Advisor will help you get what you need.
Amplifier Wiring Diagrams How to Add an Amplifier to Your Car Audio System
Normally, when you install a new stereo, all the wires from the stereo would connect to the car wiring adapter. At some point in the future I ant to ad a sub in the trunk. Find what fits your vehicle. These terminals are either the spring clip or binding post type.
- As for a head unit, without knowing what features you want or what vehicle it should fit in make it impossible to offer any meaningful recommendation.
- Any help would be appreciated as always.
- Just be sure to tape off any exposed conductors so they can't short by touching anything metal.
- Which speakers would you recommend I amplify, the front or rear?
- My question is do I need to run new thicker gauge speaker wire or will I be fine with the factory wires?
- Well, believe it or not Fred is right.
Can't find your exact vehicle? They'll come free when you order from us. Do you see any problems with this approach? If it immediately blows, it indicates there is something dreadfully wrong with the power wiring, probably a short circuit to ground.
Caution about hookup wire
Carl, Yes, postgarage you can connect that subwoofer to two bridged channels of that amp and that speaker to the other two channels bridged together. You want to ground your cap. An online search should get you in touch with a car audio dealership that can deliver to your territory.
So, two of the amp's channels will drive two speakers while the other pair of channels drive four speakers. Disconnect the negative battery terminal. Should the ground wire size match the power wire before or after the distribution block split. Choose something strong and clean sounding. But you need to be aware of some important points to ensure the best results.
The Gear Page
If you bought any of your gear from Crutchfield, you could call Tech Support for free help troubleshooting your system. Using my factory headunit. Pat, my 18 year old The simplest way to add an amplifier to a factory system is to get one that has speaker-level inputs. One question about this method though. Run the power wire to your amp.
After identifying the speaker wires, you cut each one and connect the end coming from the radio's output to the amp's input, and the end going to the car speakers to the amp's output. Nice way to help people who are still dealing with basic audio upgrades though, very easy to follow diagram. Even though I put the Bluetooth special mode in rear with subwoofer it still takes up both channels for the rear I can't split the other one. Tell us about your vehicle.
What would happen if you hooked it up and the subs blew? When I got my parts in the mail, I noticed that the hookup wire I was sent had an insulation voltage rating of V, whereas I needed the wire to carry V. It helped me hook up my system. Disconnect the factory speaker wires from the head unit and connect factory speaker wires to amp speaker wires.
The buzz is noticed first in hz tone. Oh and the remote start wire goes to the receiver too? Using factory speaker wiring for a watt amp should be okay.
Watch for simple wiring mistakes that put speakers out of phase
Electrically, it'll be connected to all the amps in your system, but it will do the most good to the nearest amp. All of the sound feels like it's stuck inside the trunk. Kris, I'm unfamiliar with that vehicle's trunk, so I can't help you with choosing a ground point. Your help is always appreciated, dr phil online thank you.
How to Wire an Amp to a Sub and Head Unit 12 Steps
Fisherman, I do not think that amplifier will tax your Honda's electrical system at all. This wiring diagram shows how a full-blown car audio system upgrade gets wired in a car. Yea I think I got it now say forward is into receiver and back means out.
How to Connect Speakers Using Speaker Wire
That V may be good to V or whatever in some cases, but only if kept within it's temperature spec. That's why articles like this Amplifier Wiring Diagram exist, to guide customers in their own installation. Any help you could provide would be appreciated. However, there are in-helmet sound systems that may work for head-banging.
Mount your amplifier on a solid surface that will not conduct electricity. What software did you use to create the wiring diagram? Both front and rear will need brackets in order to fit replacement speakers. Warnings Always Disconnect the Negative terminal from your battery before doing anything with electricity on your car. Just make sure the primary power cable, from the battery to the block, speed dating elite is large enough to accommodate the total power draw of all the amplifiers.
- Hey buck, I'll list my equipment first, then what I'm trying to do.
- Mike, That wiring kit will be fine for those two amplifiers as long as the main power cable run is no longer than about thirteen feet.
- Things You'll Need Amplifier.
- Check out our tech support page for details.