Hook up amp to sub, how to connect a subwoofer to a receiver or amplifier

It Still Works

Buck Pomerantz

Can you hook up a sub to a 2 channel stereo system

Hi Buck Apologies if off topic. Is this possible or recommended? From everything I've read on this site, this should work just fine, if not well, correct? Brand names and model numbers work best.

How to Wire an Amp & Subwoofers Into a Stock Stereo

Subwoofer connection to a two-channel system differs from the methods used in home theaters. If you want a question answered about a system, you must identify the gear by model numbers as well as brand names. Is this article up to date?

Could you possibly provide a diagram of this to help me? Any help or links would be great! My guess is I need an amp. Be careful not to give yourself an electric shock because it is quite painful. This could be caused by a bad ground.

Just make sure the gain is set to never allow distortion to play. If you blow your fuse when you try to turn the amp on, this is almost always a bad ground connection. Things You'll Need Stereo. Any idea what's going on here?

Even a high-output alternator, beefed-up wiring, and a second battery might not be enough to support this monster of a system. The only way to wire that gear together is like this. Dylan, dating speed Not knowing exactly what subwoofers you're referring to make it impossible to give advice on how to wire them together. Choose a subwoofer speaker system and amplifier that fits your car's current system and meets your audio needs. Include your email address to get a message when this question is answered.

As for a diagram, I can point you to our Amplifier wiring diagrams. Would running in stereo make the amp run hotter? Just use one set for your application. If all connections seem correct but the speaker is not functioning properly, consult an expert at your local electronics store.

How to hook up a subwoofer to a stereo system

Just set the amp gain so no distortion ever plays and your system will play safely for a long time. Wire it like this diagram. Just pretend, in the upper diagram, that the two amps share the same chassis and do not need the extra power, ground, or turn-on lead wires. What amplifier required for best effects? Now for the Remote blue wire.

They are the doubles tacked magnets. Or if either of those amps could even power those subs? Mount your amp off of the floor of your trunk so that if something leaks or spills, you do not have to replace it due to damage. How do I connect my new sub to my old amp? But a lower impedance also means more stress on the amp.

  • The wires are not grounded properly, check to make sure the surface is clean, unpainted metal.
  • The sub cuts on and off at high volume when I use the auxiliary cord to phone.
  • One amp per sub, wired like this diagram.
  • Can you recommend other subs that would pair well with my Kicker Amp?
  • This is where the output of the amplifier peaks and stays there for a split-second.

How to Connect a Subwoofer to a Receiver or Amplifier

Make sure you check your fuse box to see if there are not any burnt fuses if there are burnt fuses you might have problems with the amplifier like it won't turn on connected to the subwoofers. Check out our setting gain article for help. Or, use one positive and one negative amp terminal for the pair of subs, it doesn't matter which.

How to Wire an Amp to a Sub and Head Unit 12 Steps

How to hook up a subwoofer to a stereo system

The positive on the left side to the negative on the right side. Josh, It would be better if you had identified your gear by make and model number, so I could give accurate advice. It seems the mono's are cheaper. An amplifier will put out more power through a low-impedance sub than it will through a high-impedance sub. Mike, toyboy speed dating I see what you mean - a web search came up with a few different amplifiers with different specs.

How to Hook Up Subwoofers to an Amp

Manuel, Your subs probably blew because they were being driven with twice their rated power. Always be careful with electricity. If you bought your amp from Crutchfield, you could call Tech Support for free help troubleshooting your system. And if so, how to calculate the impedance?

If you do hook your amp up to the one-ohm setup, it will probably overheat or go into protect mode. Hook it to a fuse connected to ignition turn on, like your accessory power fuse. Which is the best way to hook them up to get more bass or do I need a bigger amp? Gauge isn't extremely important here, as long as the wire is copper, the resistance-per-foot is in the mili-ohm range, meaning there will be minuscule, if any, voltage drop across the wire.

Share your voice

How to Connect a Subwoofer to a Receiver or Amplifier

How to Install Subwoofers 14 Steps (with Pictures) - wikiHow

Shows you how to add an amplifier and subwoofer to any car stereo without changing out your stock car radio saves money. Our Car amplifier installation guide offers a more detail description. It sounds good until I turn up the volume and then the other mid and high Fender speakers over power louder than the sub. On that amp it has two speaker out puts. Is mixed impedance a concern under the following configuration?

Or does it supply each with w? Subsonic filters what should it be turned at along with the other nobs to? Make sure this wire is safe from any moving objects. Why buy from an authorized dealer? Your system needs one full-range amplifier channel for each speaker.

No Diagram Available

  1. Stereo receivers, pre-amps, and integrated amplifiers rarely have subwoofer output jacks or offer bass-management options.
  2. It doesn't sound all that great.
  3. You simply connect your speaker outs from your amp to the speaker in of the sub, then connect the speaker outs of your subs to your speakers.

Most all of them do, in fact, dating brisbane recommend precisely the placement you have adopted. It's electrically the same as in this diagram. My question is can it be possible to over power the Type R?

You should be alright as long as you never play distortion, trying to get louder bass. And I'd be more confident in any advice I give you if I knew the brand names and model numbers of your gear. Basically I just want to know if its better to have an amp that matches the subs perfectly in power output or to have a bit of headroom. Forist, A sub's impedance depends on the impedance of its voice coils, how many of them there are, and how they're wired together. Last thing you need is a dead battery.

Blake, I'm unfamiliar with that amplifier, but it'll probably work with those subs. What do you recommend on wiring? The fuse amperage should match the gauge size. Don't expect a lot of bass out of that amplifier, though - its specs are a bit exaggerated. Figure out where you're going to place the amp, put the beginning of your power red wire there and give it about a foot of wire extra, then begin to hide and run the power wire to under the hood.

Not only are you not producing a single decibel of sound during this microsecond, but you're also working the voice coil very hard and damaging it. Please advise which one and how to wire those, don't know what is the lowest impedance for K using two subs. Jameson, ddlg dating site That sub should be wired to that amp's subwoofer output like this.

  • Good icebreaker dating questions
  • What is the best type of radiometric dating to use to date an object
  • Colombian dating website
  • Dating cancelling last minute
  • What is just hook up
  • Online dating and chatting
  • Dating profile male